Home › Text & Utility › Inductance Converter
Text & Utility

Inductance Converter

A buck-converter datasheet says 100 µH, a motor nameplate says 15 mH, an RF note says 4.7 nH — three labels for the same kind of quantity in three different dialects. This page restates any inductance in henries, kilohenries, millihenries, microhenries, nanohenries, picohenries, abhenries and stathenries at once, through the henry definitions.

Free · No sign-up · Runs in your browser · First published 2026-10-25 · Updated November 2026

Everything converts through the henry. The SI steps are exact powers of a thousand: 1 kH = 10³ H, 1 mH = 10⁻³ H, 1 µH = 10⁻⁶ H, 1 nH = 10⁻⁹ H, 1 pH = 10⁻¹² H. The CGS steps are labelled approximate wherever they appear: 1 abH = 10⁻⁹ H exactly in the EMU system, and 1 stH ≈ 8.987551787 × 10¹¹ H in the ESU system. An inductance here is a size, so a negative value gets a clear error. The energy line uses E = ½LI² — it needs a current, which is why that field sits beside the converter rather than inside the table.

Converted inductance
—

One inductance, three labels

Inductance is a coil's opposition to a change in current — L = flux ÷ current, in henries, where one henry produces one volt when the current changes by one amp per second. The henry itself is far too large for ordinary electronics, so real inductors are labelled in its thousandths: microhenries on switch-mode power-supply datasheets, millihenries on motor and audio parts, nanohenries in RF notes where a few turns of wire are already too much. This page restates any inductance in all eight units at once, worked through the henry with every factor defined, so a figure in any dialect can be read in any other. It also answers the question the conversion alone cannot: at a current you enter, how much energy does this inductance actually store?

Bar chart of everyday inductances in microhenries: an RF inductor 4.7, the worked example 100, a motor choke 2,200, an audio crossover inductor 10,000 and a transformer winding 1,000,000
Everyday inductances in microhenries, drawn as bars: the worked example below sits at 100 µH = 0.1 mH.

The formula

henries = value × (henries in one "from" unit)
answer = henries ÷ (henries in one "to" unit)

Two terms, both visible on the page. value is the number you enter. henries in one "from" unit is the definition of the unit you are converting from: 10³ for the kilohenry, 1 for the henry itself, 10⁻³ for the millihenry, 10⁻⁶ for the microhenry, 10⁻⁹ for the nanohenry, 10⁻¹² for the picohenry, 10⁻⁹ for the abhenry, and approximately 8.987551787 × 10¹¹ for the stathenry. answer is the result in the unit you asked for. Every SI step is a factor of exactly a thousand — that is the whole conversion, and it is why the microhenry-to-millihenry step never needs a calculator once the pattern is seen. The abhenry and stathenry are CGS units, kept here because they still appear in old tables; the stathenry's factor is approximate because it inherits the speed of light, while the abhenry's is exact within its own system.

Worked example

Convert 100 microhenries to millihenries — the output inductor of a typical buck converter, and the value a power-supply designer reaches for first — the way the tool does it.

Step 1 — get to henries. One microhenry is 10⁻⁶ H, so 100 × 10⁻⁶ = 0.0001 H.

Step 2 — divide by the target factor. One millihenry is 10⁻³ H, so 0.0001 ÷ 0.001 = 0.1.

Step 3 — read the display. The page prints six decimals below 0.001, four below 10 and two above, so the headline reads 0.1 mH, and the detail line shows the working: 100 µH = 0.1 mH — worked through henries: 0.0001 H ÷ the Millihenry factor.

Check it. Multiplying back, 0.1 × 1,000 = 100 µH exactly, and 100 µH × 1,000 = 100,000 nH — the chain closes in both directions. The table underneath restates the same inductance in all eight units (0.0001 H, 0 kH, 0.1 mH, 100 µH, 100,000 nH, 100,000,000 pH, 100,000 abH, 0 stH), so the from/to choice only changes which row is the headline. And the energy line finishes the job for this inductor: at the default 2 A, that 100 µH stores 200 µJ of energy — E = ½LI² = 0.5 × 0.0001 × 4.

Conversions worth memorising

Every row below is the tool's own output, checked figure by figure:

FromToResult
1 Hmillihenries1,000 mH
1 Hmicrohenries1,000,000 µH
1 mHmicrohenries1,000 µH
33 µHmillihenries0.033 mH
33 µHnanohenries33,000 nH
4.7 µHnanohenries4,700 nH
10 mHhenries0.01 H
10 mHmicrohenries10,000 µH
1 µHnanohenries1,000 nH
1 nHmicrohenries0.001 µH
1 mHnanohenries1,000,000 nH
2.2 mHmicrohenries2,200 µH
470 µHmillihenries0.47 mH
1 Hnanohenries1,000,000,000 nH

Three rows deserve a second look. The first two are the whole subject in miniature: every SI step is a thousand, so moving one row in the table multiplies or divides by 1,000, and the only skill is counting how many steps you moved — 100 µH is one step below millihenries, so it is 0.1 mH, and two steps above nanohenries, so it is 100,000 nH. The 33 µH row is the buck-converter row: 33 µH is the other value power designers reach for alongside 100 µH, and it is 0.033 mH and 33,000 nH by the same two multiplications. And the 1 nH row is the RF warning: one nanohenry is a thousandth of a microhenry, which is why an RF layout treats a centimetre of PCB trace — roughly a nanohenry per millimetre — as a component in its own right, not as a wire.

Three traps worth knowing

Microhenries and millihenries differ by a thousand, and both are written with an m. The prefix is the whole value: µH is a millionth of a henry, mH is a thousandth. A datasheet that prints "100 mH" where it means "100 µH" is wrong by a factor of a thousand, and a buck converter built on that reading will not regulate — it will saturate, overheat, or both. When a value looks implausibly large for its circuit, check the prefix before doubting the circuit: board-level power inductors live in microhenries, motor windings in millihenries, and almost nothing on a board is honestly measured in whole henries.

An inductor's value is not its rating. This page converts the inductance figure, and the energy line works out what that inductance stores at your current — but neither tells you whether the part survives that current. A 100 µH inductor rated for 2 A saturates above 2 A: its inductance collapses, its current spikes, and the circuit it was protecting is suddenly unprotected. The saturation current, the DC resistance and the self-resonant frequency all live in the datasheet, and a correct conversion of an undersized part is still an undersized part.

Tiny figures hit the display floor in the kilohenry and stathenry rows. The page prints six decimals below 0.001, so 100 µH reads as 0 kH and 0 stH — the true values, 0.0000001 kH and about 0.0000000000000001 stH, round to zero at six decimals. The millihenry row is the readable one for power parts, and the nanohenry row for RF parts. Read the row on the inductor's own scale: the factor is exact, and the readable row is the one near the part's own size.

How to read your result, and the limits

Results show six decimals below 0.001, four below 10 and two above — more precision than any inductor's tolerance justifies, so round to the part for real use: a power inductor rated ±20% makes the fourth decimal meaningless. Four limits belong with the page. Negative values are refused: a negative inductance gets a clear error, because this page converts sizes. Empty input clears quietly; type and the table rebuilds, delete and the page waits. Anything past a trillion in any unit gets a clear error instead of a meaningless digit string. And this page converts units, not circuits: it will restate any inductance in any unit and work out its stored energy at your current, but it will not tell you whether that inductor suits a circuit — its saturation current, its resistance and its self-resonant frequency all live in the datasheet, and a correct conversion of the wrong part is still the wrong part.

Related tools: Capacitance Converter — Microfarads to nanofarads, picofarads, farads and more — every answer in all eight units; Electric Current Converter — Amps to milliamps, microamps and more — every answer in all eight units, plus the watts at your voltage; Ohm's Law Calculator — Enter any two of voltage, current, resistance and power — get the other two, with the working.

Frequently asked questions

How many microhenries are in a millihenry?

Exactly 1,000. So 1 mH is 1,000 µH and 1,000,000 nH, 100 µH is 0.1 mH, and 33 µH is 0.033 mH. Every SI step is a factor of a thousand: henries to millihenries to microhenries to nanohenries to picohenries.

What is a henry?

One henry is the inductance that produces one volt when the current through it changes by one ampere per second — L = flux ÷ current, in volt-seconds per ampere. It is named after Joseph Henry. Real board-level inductors are measured in microhenries and millihenries because one whole henry is far larger than any board part.

What inductance does a buck converter use?

Commonly 10 µH to 100 µH for low-voltage board supplies — 33 µH and 100 µH are the two values designers reach for first — with the exact choice set by the switching frequency, the input and output voltages and the allowed ripple current, all of which live in the controller's datasheet rather than in a unit conversion.

How much energy does an inductor store?

E = ½LI²: half the inductance times the current squared. A 100 µH inductor at 2 A stores 0.5 × 0.0001 × 4 = 0.0002 J, which is 200 µJ. Enter the current on this page and the energy line works it out for any inductance.

Ahsan ul Haq
Editor, ToolFigure

Every ToolFigure calculator is checked against hand-worked examples before it is published — the same worked examples you can follow on each page. More about ToolFigure →

Related tools

Calculators that show their working

Free forever · No sign-up · Every result comes with its formula and a worked example.

Browse all tools