Five lines that make a hardwood price: wood, labour, waste, removal, prep
A hardwood price is a material rate per square foot set by the species, times the floor area with a waste factor for cuts at the perimeter, plus the labour per square foot on the net area, plus old floor removal and subfloor prep where chosen, then multiplied by a region factor:
wood material ($) = rate per sq ft ($) × floor area (sq ft) × (1 + waste factor) — $7.50 solid oak · $7.00 engineered oak · $8.50 maple · $9.50 hickory · $12.00 walnut · $16.00 exotic; waste 10% straight lay · 15% diagonal or herringbone
labour ($) = $5.00 solid oak · $4.00 engineered oak · $5.50 maple · $5.50 hickory · $6.00 walnut · $6.50 exotic per sq ft × floor areatotal ($) = (wood material + labour + old floor removal $1.50 per sq ft + subfloor prep $1.00 per sq ft) × region factor (×0.90 low-cost · ×1.00 average · ×1.10 high-cost)price per sq ft ($) = total ÷ floor areaplanning range = total × 0.85 to total × 1.15The same formula is behind the table above, so every row can be rebuilt by hand. The worked example is 500 sq ft in solid oak with a straight lay, no removal, no prep, average region: $7.50 × 500 × 1.10 is $4,125.00 for the wood, $5.00 × 500 is $2,500.00 of labour, for $6,625.00 — $13.25 a sq ft, with a planning range of $5,631.25 to $7,618.75.
Worked example, checked against the published cost guides
Four published 2026 hardwood cost guides bracket the worked example rather than matching it to the dollar, because no two guides price the same combination — and the bracket is the honest check. CalculatorZilo's worked example for the same job — 500 sq ft of solid oak at $7.50 a sq ft, nail-down labour at $5.00 a sq ft, 8% waste and $1.50 a sq ft old-floor removal — is $7,300.00, or $14.60 a sq ft, and this page's same job with removal is $7,375.00, $75.00 above it, exactly the 2% waste difference: this page wastes 10% on a straight lay where their example wastes 8%. CostToRenovate puts a typical hardwood job at $3,000 to $12,000 with a national average of $6,500 — this page's worked example is $6,625.00 and sits inside that range. BuildRefs puts solid hardwood at $10 to $25 a sq ft installed and engineered at $7 to $20 — this page's worked example is $13.25 a sq ft and sits inside solid, and its engineered oak is $11.70 a sq ft and sits inside engineered. BuildCalcu puts new hardwood at $6 to $18 a sq ft installed — this page's worked example is $13.25 a sq ft and sits inside it — and refinishing an existing floor at $3 to $8 a sq ft, roughly a third to half of a new install. The table rows show the model's edges: a walnut herringbone job in a high-cost region is $9,812.00, a maple room is $4,455.00, and a whole-house oak job with removal and prep is $15,750.00.
How to read your result, and its limits
Four cautions keep the number honest. First, the wood is the base: the same 500 sq ft is $5,850.00 in engineered oak and $12,050.00 in exotic wood — the wood alone moves the worked example by $6,200.00 — and the difference is real, not cosmetic: solid oak is the common domestic choice, engineered oak installs faster and suits concrete subfloors, maple and hickory are harder and costlier, walnut is a premium dark wood, and exotic species push past $25 a sq ft installed. Second, the waste is on the wood only: a diagonal or herringbone pattern wastes 15% against a straight lay's 10% — the worked example as a herringbone job is $6,812.50 against $6,625.00 straight, a $187.50 difference — while the labour, the removal and the prep are charged on the actual floor area, not the area with waste. Third, measure each room and add them: length times width per room, then add the rooms — and ordering the exact floor area without the waste factor leaves you short by the waste, $375.00 of wood on the worked example. Fourth, removal and prep are separate lines: the worked example with removal is $7,375.00 and with subfloor prep is $7,125.00 — neither is inside the headline $6,625.00 — and subfloor repair, moisture barriers, stair treads and transition strips are priced separately again. The cheapest combination on this page is $1,579.50 — 150 sq ft of engineered oak with no removal in a low-cost region — and the dearest is $60,280.00, a 2,000 sq ft exotic job, herringbone, with removal and prep in a high-cost region. The region is only a proxy: the worked example is $5,962.50 in a low-cost region and $7,287.50 in a high-cost one, so only local installers settle the real number. The carpet alternative is priced by the carpet installation cost calculator, the room's area by the flooring calculator, and the tile alternative by the tile calculator.
Common mistakes
- Comparing a wood-only price with an installed price. Solid oak runs $7.50 a sq ft for the wood alone — this page is the installed job, so a $6,625.00 oak room is the finished price, not the boards: the labour adds $5.00 a sq ft.
- Forgetting the waste factor. A straight lay wastes 10% — the worked example's wood is $4,125.00, not $3,750.00 — and ordering the exact floor area leaves you $375.00 short of wood on a 500 sq ft room.
- Pricing a herringbone job like a straight lay. A diagonal or herringbone pattern wastes 15% and roughly doubles the labour on the pattern — the worked example as a herringbone job is $6,812.50, not $6,625.00 — and a quote that prices a straight lay while the job is herringbone understates it by $187.50 before the labour difference.
- Forgetting the removal. Old floor removal is $1.50 a sq ft — the worked example with removal is $7,375.00, not $6,625.00 — and a quote that omits it understates a replacement by $750.00 on a 500 sq ft room.
- Assuming refinishing costs like a new floor. Refinishing an existing floor runs $3 to $8 a sq ft — roughly a third to half of a new install — so a floor worth sanding and staining is $1,500.00 to $4,000.00 on 500 sq ft, not $6,625.00.
Frequently asked questions
How much does hardwood floor installation cost?
CostToRenovate puts a typical hardwood job at $3,000 to $12,000 with a national average of $6,500, and BuildRefs puts solid hardwood at $10 to $25 a sq ft installed. On this page, 500 sq ft in solid oak with a straight lay is $6,625.00 — $13.25 a sq ft — inside both ranges, while the same 500 sq ft in engineered oak is $5,850.00 and in exotic wood is $12,050.00.
Is engineered hardwood cheaper than solid hardwood?
Yes, on this page: 500 sq ft in engineered oak is $5,850.00 against $6,625.00 in solid oak, a $775.00 difference, because engineered oak is $7.00 a sq ft for the wood with $4.00 labour against solid oak's $7.50 and $5.00. Engineered also installs faster, especially over concrete, while solid oak can be sanded and refinished more times over its life.
How much extra hardwood do I need to order?
Measure each room's length times width in feet, add the rooms, then add the waste factor: 10% for a straight lay, 15% for a diagonal or herringbone pattern. The waste applies to the wood only — the labour, removal and prep are charged on the actual floor area — so the worked example's 500 sq ft is 550 sq ft of wood to order, and ordering the exact floor area leaves you $375.00 short of wood.
Is refinishing cheaper than installing new hardwood?
Yes, by a lot: refinishing an existing floor runs $3 to $8 a sq ft (BuildRefs, BuildCalcu) — roughly a third to half of a new install — so 500 sq ft is $1,500.00 to $4,000.00 to refinish against $6,625.00 to install new solid oak. Refinishing only works when the boards are thick enough to sand and the damage is in the finish, not the wood itself.

